General information
Slots for plug-in modules | 1 |
Mains connection
Network configurations | TN-S, TN-C-S with grounded neutral |
Mains input voltage | 3x 200 VAC to 480 VAC ±10>#/td### |
Frequency | 50 / 60 Hz ±4>#/td### |
Installed load | Max. 5 kVA |
Inrush current | Max. 45 A |
Switch-on interval | Typ. 60 s |
Integrated line filter per EN 61800-3, category C3 | No |
Power dissipation at device nominal power without braking resistor | [(50 + 6.9 * PAVG [kW] + 7.5 * (IAX1 [A] + IAX2 [A]) + 0.25 * (IBR12[A] + IBR22[A]) + PVSLOT) * 1.1] [W] |
DC bus connection
DC bus capacitance | 470 µF |
24 VDC power supply
Input voltage | 24 VDC ±25>#/td### |
Input capacitance | 5507 µF |
Current consumption | 1.2 A + Current for motor holding brake |
Motor connection
Quantity | 2 |
Continuous power per motor connection | 1 / 1 kW |
Continuous current per motor connection | 2.2 / 2.2 Aeff |
Reduction of continuous current depending on switching frequency | |
Switching frequency 5 kHz | No reduction |
Switching frequency 10 kHz | No reduction |
Switching frequency 20 kHz | No reduction |
Reduction of continuous current depending on installation elevation | |
Starting at 500 m above sea level | 0.22 Aeff per 1000 m |
Peak current per motor connection | 6 / 6 Aeff |
Peak power output | 2.5 kW |
Nominal switching frequency | 5 kHz |
Possible switching frequencies | 5 / 10 / 20 kHz |
Insulation stress of the connected motor per IEC TS 60034-25:2004 | Limit value curve A |
Protective measures | |
Overload protection | Yes |
Short circuit and ground fault protection | Yes |
Max. output frequency | 598 Hz |
Variant | |
U, V, W, PE | Connector |
Shield connection | Yes |
Terminal connection cross section | |
Flexible and fine-stranded wires | |
With wire end sleeves | 1.5 to 6 mm² |
Approbation data | |
UL/C-UL-US | 24 to 8 AWG |
CSA | 24 to 8 AWG |
Max. motor line length depending on switching frequency | |
Switching frequency 5 kHz | 75 m |
Switching frequency 10 kHz | 37.5 m |
Switching frequency 20 kHz | 18.75 m |
Motor holding brake connection
Quantity | 2 |
Output voltage | Depends on the input voltage on connector X2 |
Continuous current | 1.3 A |
Max. internal resistance | 0.25 Ω |
Extinction potential | Approx. 30 V |
Max. extinction energy per switching operation | 1.5 Ws |
Max. switching frequency | 0.5 Hz |
Protective measures | |
Overload and short-circuit protection | Yes |
Open-circuit monitoring | Yes |
Undervoltage monitoring | Yes |
Response threshold for open-circuit monitoring | Approx. 30 mA |
Braking resistor
Peak power int./ext. | 7 kW / 25 kW |
Continuous power int./ext. | 150 W / 2 kW |
Minimum braking resistance (ext.) | 25 Ω |
Enable inputs
Quantity | 2 |
Circuit | Sink |
Electrical isolation | |
Input - ACOPOS P3 | Yes |
Input - Input | Yes |
Input voltage | |
Nominal | 24 VDC |
Maximum | 30 VDC |
Input current at nominal voltage | Approx. 9 mA |
Switching threshold | |
Low | <5 V |
High | >15 V |
Switching delay at nominal input voltage | |
Enable 1 → 0, PWM off | 2 ms |
Enable 0 → 1, ready for PWM | 0.3 ms |
Modulation compared to ground potential | Max. ±38 V |
OSSD signal connections | 0.5 ms |
Encoder interfaces
Quantity | 2 |
Type | EnDat 2.2 |
Connections | 8-pin female Mini I/O connector |
Status indicators | None |
Electrical isolation | |
Encoder - ACOPOS P3 | No |
Encoder monitoring | No |
Max. encoder cable length | 100 m Depends on the cross section of the power supply wires in the encoder cable |
Encoder power supply | |
Output voltage | Typ. 11.4 V |
Load capacity | 300 mA |
Protective measures | |
Short-circuit proof | Yes |
Overload-proof | Yes |
Synchronous serial interface | |
Signal transmission | RS485 |
Data transfer rate | 6.25 Mbit/s |
Max. power consumption per encoder interface | PENCODER [W] = U24V [V] * (IENCODER [A] * 0.7) + 0.5 W |
Trigger inputs
Quantity | 2 |
Circuit | Sink |
Electrical isolation | |
Input - ACOPOS P3 | Yes |
Input - Input | Yes |
Input voltage | |
Nominal | 24 VDC |
Maximum | 30 VDC |
Switching threshold | |
Low | <5 V |
High | >15 V |
Input current at nominal voltage | Approx. 4 mA |
Switching delay | |
Rising edge | <2 µs |
Falling edge | <1 µs |
Modulation compared to ground potential | Max. ±38 V |
Support
Software | |
ACP10 | V3.12.1 |
Operating conditions
Permissible mounting orientations | |
Hanging vertically | Yes |
Standing horizontally | In preparation |
Installation elevation above sea level | |
Nominal | 0 to 500 m |
Maximum | 4000 m |
Pollution degree per EN 61800-5-1 | 2 (non-conductive pollution) |
Overvoltage category per EN 61800-5-1 | III |
Degree of protection per EN 60529 | IP20 |
Ambient conditions
Temperature | |
Operation | |
Nominal | 5 to 40°C |
Maximum | 55°C |
Storage | -25 to 55°C |
Transport | -25 to 70°C |
Relative humidity | |
Operation | 5 to 85%, non-condensing |
Storage | 5 to 95>#/td### |
Transport | 95% at 40°C |
Mechanical properties
Dimensions | |
Width | 66 mm |
Height | 374 mm |
Depth | |
Wall mounting | 258.5 mm (with 8EXA front cover: 261 mm) |
Weight | 4 kg |
Brands:
B&R AUTOMATION
Condition:
new
Price history
As soon as the price of the products decreases, you will immediately know about it.
The price has not changed yet. We will show it on this chart once it changes