MATERIAL NUMBER:
8BVI0110HWD0.000-1
DESCRIPTION:
- Integrated uncontrolled standstill and safe stop
- Integrated connection for motor holding brake and temperature sensor
- 2 slots for ACOPOSmulti plug-in modules
- Two fully independent power inverters in one inverter module contained in 2-axis modules
ACOPOSmulti inverter module, 15.1 A, AS, wall mounting, 2 axes
General information
| B&R ID code | 0xA8E5 |
| Cooling and mounting type | Wall mounting |
| Slots for plug-in modules | 2 |
| Certifications | |
| CE | Yes |
| Functional safety | Yes |
| UL | cULus E225616
Power conversion equipment |
| EAC | Yes |
| KC | Yes |
DC bus connection
| Voltage | |
| Nominal | 750 VDC |
| Continuous power consumption | 22.3 kW |
| Power dissipation depending on switching frequency | |
| Switching frequency 5 kHz | [0.33 * IM² + 11 * IM + 90] W |
| Switching frequency 10 kHz | [0.97 * IM² + 9.5 * IM + 170] W |
| Switching frequency 20 kHz | [1.66 * IM² + 21 * IM + 380] W |
| DC bus capacitance | 660 µF |
| Variant | ACOPOSmulti backplane |
24 VDC power supply
| Input voltage | 25 VDC ±1.6>#/td### |
| Input capacitance | 23.5 µF |
| Max. power consumption | 20 W + PSLOT1 + PSLOT2 + P24 V Out + PHoldingBrake(s) |
| Variant | ACOPOSmulti backplane |
24 VDC output
| Quantity | 2 |
| Output voltage | |
| DC bus voltage (UDC): 260 to 315 VDC | 25 VDC * (UDC/315) |
| DC bus voltage (UDC): 315 to 800 VDC | 24 VDC ±6>#/td### |
| Fuse protection | 250 mA (slow-blow) electronic, automatic reset |
Motor connection
| Quantity | 2 |
| Continuous power per motor connection | 11 kW |
| Continuous current per motor connection | 15.1 Aeff |
| Reduction of continuous current depending on switching frequency | |
| Switching frequency 5 kHz | No reduction |
| Switching frequency 10 kHz | 0.19 A/K (starting at 29°C) |
| Switching frequency 20 kHz | 0.15 A/K (starting at -38°C) |
| Reduction of continuous current depending on installation elevation | |
| Starting at 500 m above sea level | 1.51 Aeff per 1000 m |
| Peak current per motor connection | 37.7 Aeff |
| Nominal switching frequency | 5 kHz |
| Possible switching frequencies | 5 / 10 / 20 kHz |
| Insulation stress of the connected motor per IEC TS 60034-25:2004 | Limit value curve A |
| Protective measures | |
| Overload protection | Yes |
| Short-circuit and ground fault protection | Yes |
| Max. output frequency | 598 Hz |
| Variant | |
| U, V, W, PE | Connector |
| Shield connection | Yes |
| Terminal connection cross section | |
| Flexible and fine-stranded wires | |
| With wire end sleeves | 0.25 to 6 mm² |
| Approbation data | |
| UL/C-UL-US | 30 to 10 AWG |
| CSA | 28 to 10 AWG |
| Terminal cable cross section dimension of shield connection | 12 to 22 mm |
| Max. motor line length depending on switching frequency | |
| Switching frequency 5 kHz | 25 m |
| Switching frequency 10 kHz | 25 m |
| Switching frequency 20 kHz | 10 m |
Motor holding brake connection
| Quantity | 2 |
| Output voltage | 24 VDC +5.8% / -0% |
| Continuous current per connection | 2.1 A |
| Max. internal resistance | 0.3 Ω |
| Extinction potential | Approx. 30 V |
| Max. extinction energy per switching operation | 3 Ws |
| Max. switching frequency | 0.5 Hz |
| Protective measures | |
| Overload and short-circuit protection | Yes |
| Open-circuit monitoring | Yes |
| Undervoltage monitoring | Yes |
| Response threshold for open-circuit monitoring | Approx. 0.5 A |
| Response threshold for undervoltage monitoring | 24 VDC +0% / -4>#/td### |
Enable inputs
| Quantity | 4 (2 per axis) |
| Circuit | Sink |
| Electrical isolation | |
| Input - Inverter module | Yes |
| Input - Input | Yes |
| Input voltage | |
| Nominal | 24 VDC |
| Maximum | 30 VDC |
| Input current at nominal voltage | Approx. 30 mA |
| Switching threshold | |
| Low | <5 V |
| High | >15 V |
| Switching delay at nominal input voltage | |
| Enable 1 → 0, PWM off | Max. 20.5 ms |
| Enable 0 → 1, ready for PWM | Max. 100 µs |
| Modulation compared to ground potential | Max. ±38 V |
| OSSD signal connections | Permitted
Max. test pulse length: 500 µs |
Trigger inputs
| Quantity | 2 |
| Circuit | Sink |
| Electrical isolation | |
| Input - Inverter module | Yes |
| Input - Input | Yes |
| Input voltage | |
| Nominal | 24 VDC |
| Maximum | 30 VDC |
| Switching threshold | |
| Low | <5 V |
| High | >15 V |
| Input current at nominal voltage | Approx. 10 mA |
| Switching delay | |
| Rising edge | 52 µs ±0.5 µs (digitally filtered) |
| Falling edge | 53 µs ±0.5 µs (digitally filtered) |
| Modulation compared to ground potential | Max. ±38 V |
Electrical properties
| Discharge capacitance | 0.44 µF |
Operating conditions
| Permissible mounting orientations | |
| Hanging vertically | Yes |
| Horizontal, face up | Yes |
| Standing horizontally | No |
| Installation elevation above sea level | |
| Nominal | 0 to 500 m |
| Maximum | 4000 m |
| Pollution degree per EN 61800-5-1 | 2 (non-conductive pollution) |
| Overvoltage category per EN 61800-5-1 | III |
| Degree of protection per EN 60529 | IP20 |
Ambient conditions
| Temperature | |
| Operation | |
| Nominal | 5 to 40°C |
| Maximum | 55°C |
| Storage | -25 to 55°C |
| Transport | -25 to 70°C |
| Relative humidity | |
| Operation | 5 to 85>#/td### |
| Storage | 5 to 95>#/td### |
| Transport | Max. 95% at 40°C |
Mechanical properties
| Dimensions | |
| Width | 106.5 mm |
| Height | 317 mm |
| Depth | |
| Wall mounting | 263 mm |
| Weight | Approx. 5.3 kg |
| Module width | 2 |
